SMT Solder Paste Manufacturers.
Focused on SMT soldering processes, a one-stop electronic soldering solutions provider.
Here you can find knowledge about Board Cleaner, including but not limited to usage methods, installation techniques, troubleshooting and more. Focused on SMT soldering processes. If you can't find what you need, please contact us anytime.
The R&D of solder ODM focuses on the welding pain points of thick copper boards and high-frequency boards. By adjusting the activity of the rosin system, the sphericity and particle size distribution of metal powder, as well as the viscosity and thixotropy of the carrier, it improves the melting and spreading ability without sacrificing printing accuracy, and solves production-line-level problems such as insufficient wetting caused by fast heat dissipation of thick copper and residual ion migration caused by sensitivity to dielectric loss of high-frequency boards.
Published: 2023-05-01Circuit board soldering faces multiple challenges of high reliability, fine pitch, and heat-sensitive components in the medical, communication, and new energy sectors. Based on practical production line experience, this paper focuses on key processes such as solder paste selection, stencil aperture design, reflow profile optimization, and BGA rework, emphasizing solder joint wettability, void rate control, and cold solder joint identification methods. All parameters are derived from measured data from Jia Jinyuan production lines, without theoretical deduction.
Published: 2023-01-22QFN soldering on new energy electronic control boards faces dual challenges of high-frequency vibration and thermal cycling. By optimizing stencil aperture design, reflow profile, and pad design, Jiajinyuan has increased the thrust of QFN solder joints to over 28N, with the IMC layer thickness controlled at 3.2μm±0.4μm, effectively suppressing microcrack propagation and meeting the long-term reliability requirements of automotive-grade IPX7 protection and operating conditions ranging from -40℃ to 125℃.
Published: 2022-12-11For soldering gold-plated boards, it is necessary to balance the thickness of the pad gold layer with the activity matching of the flux to avoid black pad, cold solder joints, and excessive IMC growth. Jia Jinyuan's gold-plated board soldering solution has achieved a soldering defect rate below 0.3% in aerospace modules and medical equipment, with the key lying in the collaborative implementation of solder paste selection, reflow profile gradient control, and an oxygen content ≤100ppm under a nitrogen atmosphere.
Published: 2022-11-255G device solder must meet the dual stringent requirements of high-frequency signal integrity and thermal cycle reliability. Jinyuan JNY-5G188 lead-free solder achieves zero void rate soldering in scenarios such as base station power amplifier modules and router RF motherboards. Its low-silver ratio and active flux synergistically optimize wetting speed and residue insulation.
Published: 2022-11-11Manual soldering is an irreplaceable key process in circuit board repair and rework. Especially during BGA rework, 0201 component touch-up soldering, and operations in heat-sensitive areas of multilayer boards, the coordinated matching of soldering iron temperature, solder wire activity, and solder paste rheological properties directly determines solder joint reliability. Jiajinyuan solder paste stands out in low-temperature wettability, residue insulation, and reflow stability. When used with constant-temperature soldering irons and micro-diameter soldering tips, it can significantly reduce the risk of thermal damage.
Published: 2022-09-05
If solder paste is improperly selected or incompletely cleaned during PCB soldering, residual halide ions and moisture will act together to trigger electrochemical migration, leading to corrosion of copper circuits on the PCB, reduced insulation resistance, and severely compromised long-term reliability, with the failure risk rising significantly especially in high-temperature and high-humidity environments.
Published: 2022-07-23Due to the large heat capacity and high thermal conductivity of copper, thick copper board soldering suffers from delayed temperature rise and easily low peak temperature during reflow soldering. The soaking zone must be extended to 150–180 seconds to ensure sufficient melting and wetting of the solder paste; otherwise, defects such as cold solder joints, dry joints, and dull solder joints occur frequently. Actual measurements on Jia Jinyuan's production line show that when the soaking zone is less than 140 seconds, the void rate of BGA solder joints increases by 37%.
Published: 2022-07-20ENIG gold-plated PCB boards in SMT production lines often suffer from cold solder joints and poor wettability due to nickel layer oxidation, abnormal gold layer thickness, or mismatched solder paste activity. Solder paste compatibility must take into account both the intermetallic compound growth window of ENIG solder paste and the PCB surface condition, with key control over the flux acid value, active temperature range, and metal powder sphericity in the solder paste to avoid excessive metallographic dissolution or insufficient IMC formation.
Published: 2022-03-14To address the issue of warpage that easily occurs in thin PCB boards during solder paste soldering, this paper starts from the rheological properties, metal content, thixotropic index of solder paste and the volatilization behavior of flux, proposes a selection and process coordination scheme adapted to thin board solder paste, and emphasizes the practical effects of low-stress solder paste, medium-low temperature reflow window and fine-tuning of printing parameters on suppressing warpage.
Published: 2021-09-06Our technical team is always ready to provide professional solder material selection advice and SMT process solutions.