SMT Solder Paste Manufacturers.
Focused on SMT soldering processes, a one-stop electronic soldering solutions provider.
Here you can find knowledge about Low-Void Solder Paste, including but not limited to usage methods, installation techniques, troubleshooting and more. Focused on SMT soldering processes. If you can't find what you need, please contact us anytime.
To address the challenge of void rate control in automotive lamp welding, the LFP?5RR?305 halogen-free REACH solder paste is an ideal choice thanks to its extremely low void rate and high reliability. It is suitable for precision welding in high-heat scenarios, effectively improving product yield and stability.
Published: 2026-08-28Void-free nitrogen reflow combined with low-void solder paste can reduce the void ratio of BGA solder joints from 15% to below 3%. This combination has been stably running on Jia Jinyuan's production line for over 2 million units. The key is that nitrogen purity must be maintained above 99.995% with oxygen content below 50 ppm. Combined with the thixotropy optimization and activator gradient volatilization design of Jia Jinyuan LDS-702 low-void solder paste, voids are effectively suppressed in the early stage of reflow.
Published: 2025-05-26During the rework soldering and BGA chip ball mounting process, an excessive void rate is the main cause of cold solder joints, increased thermal resistance, and early failures. Using low-void solder paste can significantly improve the metallurgical bonding quality of solder joints, and especially maintain structural integrity after multiple thermal cycles. In actual tests, the Jiajinyuan JGY-850 series solder paste stably controls the void rate within 8%. Combined with precise stencil aperture design and nitrogen-protected reflow, it increases the first-pass yield of rework soldering to 98.3%.
Published: 2024-02-28
For BGA high-density packaging scenarios, Jiajinyuan's halogen-free, low-void solder paste 8M9P/5RR series has completed production line verification at leading packaging and testing customers. The measured void rate is stably controlled within 3%. After reflow soldering, the solder joints exhibit uniform wetting and a dense, continuous IMC layer, raising the first-pass yield of BGA devices from 92.7%
Published: 2021-07-14When soldering 5G devices on high-frequency PCBs, solder faces the practical issue of increased void rate that exacerbates signal attenuation. By optimizing metal content, rheological properties, and flux volatilization pathways, low-void solder paste has been verified on actual production lines of the Jiajinyuan JH-5G series, stably controlling the void rate of BGA solder joints within 8%, significantly improving the impedance continuity and return loss performance of RF modules in the millimeter-wave frequency band.
Published: 2021-01-19The solder used in energy storage modules is extremely sensitive to voiding rate. Low-void solder paste can control the voiding rate of BGA solder joints within 5%, significantly improving the thermal fatigue life of electronic control boards under high-power cycling. Jiajinyuan JY-810A solder paste, with its stable thixotropy, low residue, and reflow wetting angle of less than 25°, has become a practical combination for BGA soldering of electronic control boards in the selection of solder materials for energy storage modules.
Published: 2017-04-04Excessive solder paste voiding rate of the thermal pad at the bottom of QFN is a high-frequency failure on SMT production lines, requiring coordinated optimization from four aspects: solder paste selection, stencil aperture design, printing parameters, and reflow profile. Although low-void solder paste can reduce the voiding rate, it cannot replace process matching. The squeegee pressure and speed, nitrogen purity, and temperature gradient of each reflow zone must be adjusted in accordance with the actual equipment status of the production line.
Published: 2016-03-21BGA soldering quality is highly dependent on the rheological properties and reflow behavior of solder paste. Low-void solder paste, by optimizing metal content, flux activity and particle distribution, significantly reduces solder joint void rate to below 3% in actual production lines, and has become a core material for improving BGA soldering first-pass yield and long-term reliability.
Published: 2014-12-05High-frequency board welding is extremely sensitive to solder paste voiding rate. Dielectric parameter fluctuations caused by voids directly degrade signal integrity. Jiajinyuan low-void solder paste, by optimizing metal content, flux volatilization gradient and reflow wetting dynamics, stably controls the voiding rate of BGA solder joints within 3.2% in 5G RF module tests, significantly suppressing insertion loss drift in high frequency bands.
Published: 2013-05-22When soldering BGA/QFN chips via SMT, an excessive void rate can lead to cold solder joints, increased thermal resistance, and early failure, and low-void solder paste is the core solution to this problem. The void rate of Jiajinyuan JL-808 series solder paste is stably controlled below 8% in mass production. Combined with optimized stencil aperture design and nitrogen-protected reflow, it can reduce the void rate at the bottom of QFN packages from 25% to 6.3%, while the void rate of individual BGA balls is simultaneously reduced to 4.1%.
Published: 2013-03-25Our technical team is always ready to provide professional solder material selection advice and SMT process solutions.