SMT Solder Paste Manufacturers.
Focused on SMT soldering processes, a one-stop electronic soldering solutions provider.
Here you can find knowledge about Solder Paste Production, including but not limited to usage methods, installation techniques, troubleshooting and more. Focused on SMT soldering processes. If you can't find what you need, please contact us anytime.
Abnormal solder paste viscosity during SMT soldering of fine-pitch chips can lead to typical defects such as solder bridging, insufficient solder, and misalignment. Based on real production line fault scenarios, this paper analyzes the causal chain between solder paste viscosity fluctuations and mismatched stencil printing parameters, and provides emergency and fundamental solutions including fine-tuning of squeegee pressure, environmental temperature and humidity control, and standardization of solder paste warm-up and stirring.
Published: 2026-08-27
In BGA reballing and soldering, the amount of solder paste used and the temperature process directly affect solder ball formation rate and solder joint reliability. Based on 20 years of production line experience, this article systematically outlines 12 key control points, covering solder paste selection, stencil aperture design, printing parameter matching, reflow profile zone setting, and common defect attribution. All recommendations are verified through real mass production.
Published: 2026-08-27
Solder paste mixing and solder paste warming are hidden cost black holes in SMT production lines. Standardized operations can reduce solder paste scrap rate by 12%, reduce printing defect rate by 3.8%, and extend stencil life by 20%. Based on 20 years of production line measured data, this article provides 6 immediately executable cost-reduction actions, covering real scenarios such as warming time control, mixing method switching, environmental temperature and humidity linkage, and batch management optimization.
Published: 2026-08-27
Nitrogen reflow soldering significantly reduces void rate and improves solder joint wettability and reliability by precisely controlling the dew point inside the oven and the oxygen content of the solder paste. It is especially suitable for mass production soldering of high-density fine-pitch devices such as 01005, QFN, and BGA. Measured data shows that under conditions of -40℃ dew point and 100ppm oxygen content, the void rate of BGA solder joints can be stably controlled within 5%.
Published: 2026-08-27
The soldering quality of QFN is highly dependent on the coordinated control of SMT stencil aperture design and reflow process parameters. IPC-7525B explicitly requires that the pad aperture area ratio be no less than 0.66, and the optimal range in actual production lines is 0.72~0.78. A ratio below 0.62 will cause the cold solder joint rate to rise sharply by more than 12%. If the reflow peak temperature deviates from the 260℃±5℃ range specified in JEDEC J-STD-020, the void rate of QFN bottom solder joints may exceed the Level 3 limit of 25% stipulated in IPC-A-610E.
Published: 2026-08-27
The selection of wave soldering bars requires comprehensive consideration of core parameters such as melting point, oxidation resistance, and copper corrosion rate. The typical Sn63/Pb37 solder bar has a melting point of 183°C, while that of Sn99.3/Cu0.7 is 227°C. The key to solder dross treatment lies in controlling the thickness of the liquid surface oxide film and the angle of the scraper. It is recommended to set the inclination angle of the scraper between 5° and 8°, and cooperate with mechanical scraping every 4 hours and nitrogen protection.
Published: 2026-08-27
Manual SMT rework soldering must precisely match solder wire diameter, soldering iron power, and actual soldering temperature; otherwise, cold solder joints, pad peeling, or thermal damage to components are highly likely to occur. Based on high-frequency production line fault cases, this paper compares the differences in temperature response curves, wetting speed, and solder joint morphology between 0.3mm and 0.5mm solder wires in typical scenarios such as QFN16, 0402 resistors, and shield can three-point grounding. It clearly points out that 0.3mm solder wire paired with a 35W soldering iron at 280℃ is more suitable for precision component rework soldering, while 0.5mm solder wire requires a soldering iron of 50W or above set at 320℃ to ensure the heat conduction efficiency of large pads.
Published: 2026-08-27
The reflow profile settings for SAC305 solder paste directly affect solder joint wettability, void rate, and component reliability. Based on 20 years of production line measurement experience, this paper analyzes the causes of key parameter mismatches in each stage of preheating, soaking, reflow, and cooling for SAC305 solder paste, focusing on common soldering defects. It also provides immediately actionable practical solutions such as temperature bandwidth adjustment, chain speed fine-tuning, and thermocouple measurement calibration, while highlighting the hidden impacts of stencil aperture design, ambient temperature and humidity, and nitrogen purity on reflow profile stability.
Published: 2026-08-27
The SMT solder paste operation process covers five major stages: thawing, stirring, printing, component placement, and reflow soldering. The core of cost reduction across the entire process lies in reducing solder paste waste, extending stencil life, lowering the rework rate, and optimizing equipment energy consumption. Based on real production line data, this paper proposes 8 actionable measures covering four dimensions: personnel operation, parameter setting, auxiliary material management, and equipment maintenance.
Published: 2026-08-27
PCB pad plating directly affects solder paste wettability. Different plating types exhibit significant differences in interfacial reaction rate, intermetallic compound formation, and oxidation tendency during the reflow phase, leading to frequent defects such as cold solder joints, tombstoning, and poor solder wetting. Based on real production line failure cases, this article directly addresses the practical performance differences of mainstream plating types including ENIG, OSP, immersion silver, and HASL across solder paste printing, component placement, and reflow stages.
Published: 2026-08-27Our technical team is always ready to provide professional solder material selection advice and SMT process solutions.