SMT Solder Paste Manufacturers.
Focused on SMT soldering processes, a one-stop electronic soldering solutions provider.
Here you can find knowledge about Solder Melting Point, including but not limited to usage methods, installation techniques, troubleshooting and more. Focused on SMT soldering processes. If you can't find what you need, please contact us anytime.
Jiajinyuan 5RLJ laser solder paste is optimized specifically for laser heating soldering scenarios. It adopts a synergistic design of rosin-based systems with multiple specifications of high-temperature alloy powders including 0307/105/305 and 00507BN, delivering stable performance with bright solder joints and no solder ball spattering within the 240–260℃ soldering window. Halogen
Published: 2020-02-19To address common issues such as cold soldering, poor wetting, and solder beads that frequently occur in the high-volume production of consumer electronics motherboards with OSP boards, this solution is based on measured production line data from Jia Jinyuan, focusing on four key measures: stencil aperture optimization, dynamic nitrogen concentration control, reflow oven temperature zone gradient matching, and AOI false alarm rate reduction. It stably improves the first-pass yield of OSP board soldering to 99.23%, with a single-line daily output exceeding 8500 units.
Published: 2020-02-17
Halogen-free solder paste is an eco-friendly solder paste that complies with RoHS and IEC 61249-2-21 standards. Its core feature is that the flux contains no halogen elements (such as chlorine and bromine) at all, while ordinary solder paste often contains halogen activators to improve wettability. There are essential differences between the two in terms of soldering reliability, ionic contamination, PCB corrosion risk, and ICT test yield.
Published: 2020-01-15
Whether flux paste must be cleaned after SMT soldering depends on the chemical activity and ion content of the flux residue, as well as the requirements of subsequent assembly processes. No-clean flux paste is not completely residue-free; rather, its flux residue becomes inert and low-corrosive after reflow. However, high-density BGA or aerospace-grade products still require cleaning to mitigate the risk of long-term electrochemical migration.
Published: 2019-12-31The head-in-pillow effect caused by solder paste defects and X-ray void defects in BGA soldering require coordinated troubleshooting from four aspects: solder paste selection, stencil design, printing parameters, and reflow profile. Insufficient wetting, uneven flux volatilization, or pad oxidation during the solder paste soldering process will exacerbate solder paste defect manifestations. Combining X-Ray image features can quickly identify the root cause of voids.
Published: 2019-12-14Solder auxiliary materials are indispensable supporting consumables in the PCBA soldering process, among which flux and PCB cleaning solvent directly affect soldering wettability, residue control and subsequent reliability. The Jiajinyuan series flux is compatible with 0201 to QFN0.4mm pads in SMT reflow soldering and wave soldering scenarios. Its rosin-based active ingredients take effect at 150℃ and complete activation at 235℃. When used with Jiajinyuan halogen-free PCB cleaning solvent, the ROSE method ion contamination value can be achieved <0.78μg/cm2.
Published: 2019-12-02
Flux paste residues do carry a risk of moisture absorption after long-term storage, which can significantly reduce the insulation reliability of PCBs, especially in high-humidity environments. In actual production lines, leakage failures between adjacent pads caused by moisture absorption of uncleaned rosin-based flux paste have occurred multiple times, and this problem is particularly prominent in enclosed areas such as under BGA and fine-pitch QFN.
Published: 2019-11-08The full range of SGS solder lead-free and halogen-free solder pastes, solder wires, and solder bars complies with RoHS and IEC 61249-2-21 standards. The solder paste supplied by Jiajinyuan delivers a stable yield of 99.2% in 0.3mm fine-pitch QFN printing, with post-reflow residue ionic contamination below 0.8μg/cm² NaCl equivalent, making it suitable for soldering automotive MCUs and high-density FPC rigid-flex boards.
Published: 2019-11-01When the fine line spacing in FPC soldering is less than 0.15mm, solder paste printing offset or collapse can very easily cause bridging short circuits. The thixotropic index and reflow behavior of JJY solder paste must match the FPC pad opening ratio and stencil thickness. By controlling squeegee pressure, speed and angle to synergistically optimize solder volume distribution, solder climbing to adjacent lines during the reflow stage can be avoided.
Published: 2019-10-18When delivering foreign trade orders, solder manufacturers must provide complete inspection documents simultaneously, including SGS reports, RoHS/REACH compliance certificates, measured melting point and wettability data, batch shipment inspection records, and packaging and transportation temperature and humidity monitoring records. These documents directly determine customer customs clearance efficiency and production line first-pass yield. Jia Jinyuan solder manufacturer has embedded standardized inspection documents into its ERP delivery process.
Published: 2019-10-04Our technical team is always ready to provide professional solder material selection advice and SMT process solutions.