Bi segregation in low temp Solder Paste arises from the inherent immiscibility between Bi and Sn in the Sn-Bi eutectic system, especially when local cooling rates deviate from ideal conditions during reflow, causing Bi-rich phases to concentrate at grain boundaries or near component terminations, which directly compromises mechanical strength and thermal cycling endurance. Because Bi has a significantly higher melting point than Sn and lower diffusivity in the molten state, uneven heat distribution across the stencil-applied deposit amplifies microstructural heterogeneity unless both paste formulation and process parameters are tightly synchronized. The viscosity profile of the Flux vehicle must therefore support uniform particle suspension during storage and printing while enabling rapid, symmetric collapse during preheat to minimize solute migration before nucleation begins.
低温焊膏通常在 180°C 以下运行，许多配方的目标回流温度在 165°C 至 175°C 之间，以保护热敏元件（例如 MLCC 和集成天线），但这种狭窄的热窗口在控制 Bi 相分离方面几乎没有留下任何误差余地，因为即使带速或区域温度有 3°C 的偏差，也足以改变凝固动力学，从而促进树枝晶 Bi 沿着先前的液体通道分离。当使用氮气气氛回流时，氧气减少改善了润湿性，但也延长了边缘区域高于液相线的时间，从而增加了密度驱动的 Bi 上浮的机会，除非合金颗粒尺寸分布缩小到 D90 <12>
Flux chemistry plays a decisive role in Bi segregation control because organic acids and halide-free activators influence both oxide removal efficiency and surface tension gradients during melting, and excessive rosin residue polarity can anchor Bi clusters at the solder–pad interface if the tack life exceeds 45 minutes under ambient humidity above 60 %RH. Printing speed must remain between 25 mm/s and 40 mm/s to balance transfer efficiency against shear-induced particle displacement, while squeegee pressure should be maintained at 4.5 ± 0.3 kgf to avoid smearing that forces Bi-enriched fractions toward deposit edges. Reflow profiles demand a ramp-to-peak rate no greater than 0.8 °C/s up to 150 °C, followed by a controlled soak between 155 °C and 162 °C for 60–90 seconds to homogenize temperature across the board before entering the liquidus zone, where dwell time above 165 °C must not exceed 45 seconds to prevent coarsening of Bi precipitates. Post-reflow inspection using cross-sectional SEM-EDS consistently reveals Bi segregation severity correlates more strongly with peak temperature overshoot than with total time above liquidus, confirming that transient thermal spikes, not duration, are the dominant driver of phase instability.
Storage conditions directly affect segregation propensity, as aging at 25 °C for more than 72 hours causes measurable Bi particle agglomeration due to weak van der Waals attraction overcoming steric stabilization from polymer dispersants, especially when paste batch lot numbers indicate post-mixing intervals exceeding 14 days. Re-mixing via centrifugal shear at 1200 rpm for 90 seconds restores dispersion uniformity only if performed before gelation onset, which occurs at 35 °C after 120 hours regardless of initial viscosity grade. Incoming inspection of solder paste must include dynamic viscosity sweep testing from 0.1 s⁻¹ to 100 s⁻¹ at 25 °C to verify thixotropic recovery remains above 88 % after 300 seconds, since degraded recovery signals weakened particle encapsulation and precedes observable Bi banding in printed deposits. Any deviation in metal load beyond 88.5 ± 0.3 wt% triggers immediate quarantine because excess Sn dilutes Bi’s lattice inhibition effect and accelerates intergranular diffusion during solidification.
